Handgun Services
Please note that prices listed are for labor only and do not include cost of parts or refinishing if any, unless specified.
| Install Full Fit NM Barrel- Does not include fitting of Match barrel bushing, barrel link or throating of barrel and frame | $225.00 |
| Fit Match Barrel Bushing | $65.00 |
| Fit Long Barrel Link | $15.00 |
| Recrown Barrel 11° | $45.00 |
| Throat Barrel and Frame for Reliable Feeding | $65.00 |
| Deburr Breech Face, Polish Center Rail and Slide Bore | $65.00 |
| Lower Ejection Port for Reliable Ejection | $45.00 |
| Cut Ejection Port Bullet Nose Relief- Aids in ejection of live rounds when using an Extended Ejector | $40.00 |
| Install and Fit New Extractor or Radius and Tension Existing Extractor | $35.00 |
| Install New Ejector | $35.00 |
| Install New Plunger Tube | $30.00 |
| Install New Grip Screw Bushing (each) | $5.00 |
| Repair Damaged Grip Screw Bushing Hole in Frame (each) | $15.00 |
| Install New Thumb Safety | $35.00 |
| Install New Amby Safety- Does not include modifying grips if required | $60.00 |
| Repair Improperly Fitted Thumb Safety by Welding and Refitting to Block Sear Properly | $35.00 |
| Install Standard .220"/.250" radius Beavertail Grip Safety- Includes machining frame for proper radius, fitting of grip safety to frame and trigger and blending of grip safety to frame | $120.00 |
| Repair Improperly Fitted Grip Safety- Weld and refit grip safety arm to properly block trigger | $35.00 |
| Install Oversize Match Aluminum Trigger and Set Overtravel Stop | $35.00 |
| Standard Trigger Job 4 to 4-3/4 pounds- Requires replacement of all MIM or substandard parts | $135.00 |
| Target Trigger Job 3 to 3-3/4 pounds- Requires replacement of all MIM or substandard parts | $150.00 |
| Note: All Series 80 type pistols require those specific parts to be installed and functioning properly for us to perform any work | |
| Drill Full Length Guide Rod for Captured Takedown- Gov't or Commander. (No Tungsten Guide Rods) | $15.00 |
Please note that prices listed are for labor only and do not include cost of parts or refinishing if any, unless specified.
| Standard Trigger Job- Trigger pull adjusted to 4 to 5 pounds. Requires a CNC Sear and on MKIII's an Improved Sear Lever. Magazine Disconnect is removed | $185.00 |
| Target Trigger Job- Trigger pull adjusted to 3 to 3-3/4 pounds. Requires a CNC Sear and on MKIII's an Improved Sear Lever. Magazine Disconnect is removed | $265.00 |
| Install Improved Sear Lever in a MKIII | $65.00 |
| Deburr Breech Face and Polish Center Rail | $65.00 |
| Adjust Extractor for Reliability | $15.00 |
| Install Full Fit Match Barrel- Does not include Modifying Feed Ramp or Recrown | $85.00 |
| Modify Barrel Feed Ramp | $50.00 |
| Recrown Barrel 11° | $45.00 |
| Install New Thumb Safety | $40.00 |
| Repair Improperly Fitted Thumb Safety by Welding and Refitting | $50.00 |
| Modify Magazine to Feed Properly | $30.00 |
| Install New Magazine Spring | $5.00 |
We work on most J, K, L and N Frame Revolvers.
Please note that prices listed are for labor only and do not include cost of parts or refinishing if any, unless specified. Be aware that certain Repair Work may require additional work for proper completion.
| Action Job- Results in a SA trigger pull of 2-3/4 to 3-1/2 pounds and overall reduction in the DA trigger pull | $125.00 |
| Smooth, Radius and Polish Trigger- Produces a better contact surface for the trigger finger | $60.00 |
| Install Non Adjustable Trigger Overtravel Stop- Does not protrude through trigger face (Not available for "J" Frame) | $65.00 |
| Install New Factory Barrel or Set Back Barrel One Turn | $145.00 |
| Recrown Barrel 11° | $65.00 |
| Correct Cylinder Endshake | $65.00 |
| Retime Cylinder | $125.00 |
| Straighten Yoke | $35.00 |
| Install Ball Detent in Yoke- (L & N Frames only) | $50.00 |
| Straighten Ejector Rod | $65.00 |
| Install New Cylinder | $125.00 |
| Correct Barrel/Cylinder Alignment | $95.00 |
| Correct Cylinder Face Runout or Shorten Cylinder Face | $125.00 |
| Chamfer Chambers for Speed Loading | $50.00 |
| Number Chambers | $25.00 |
| Correct Hard Extraction on .22 Rimfires | $65.00 |
| Install Replacement Adjustable Rear Sight Blade | $40.00 |
| Install New Front Sight Blade in Pin On Front Sight Barrels | $30.00 |
We offer services for select models. The models we accept are the Old Model Python along with all the other "E" & "I" Frame Models, Diamondback and Detective Special along with all the other "D" Frame Models. We do not accept the Magnum Carry, SF-VI or DS-II. At this time the only current production revolver I accept is the New Model Python.
Please note that prices listed are for labor only and do not include cost of parts or refinishing if any, unless specified. Be aware that certain Repair Work may require additional work for proper completion.
| Standard Action Job | $225.00 |
| Deluxe Action Job- For Python (E&I Action) | $325.00 |
| Lighten SA trigger pull on New Model Python | $125.00 |
| Install New Factory Barrel or Set Barrel Back One Turn | $145.00 |
| Recrown Barrel 11° | $50.00 |
| Correct Cylinder Endshake | $85.00 |
| Retime Cylinder | $125.00 |
| Correct Cylinder Bolt Timing | $165.00 |
| Straighten Crane | $45.00 |
| Correct Cylinder Latch not closing on New Model Python | $95.00 |
| Correct Barrel/Cylinder Alignment | $95.00 |
| Chamfer Chambers for Speed Loading | $60.00 |
| Install New Cylinder | $125.00 |
| Correct Hammer Hitting Rebound | $70.00 |
Colt Woodsman-
We offer repair of the Colt Woodsman series of pistols. We ask that you inquire with your needs. (Please be aware that we do not offer polishing or bluing in regard to any refinishing work)
Ruger Bearcat-
We offer rechambering of .22lr cylinders to .22 WRM. We do not remark the cylinder after conversion. Main cylinder must be 1.400" in length. Very early cylinders are shorter and not suitable for conversion. Price is $90.00